Strawberry Keychain
- Difficulty
- 1/3
- Weirdness
- 1/5
- Times crocheted
- 0
Free crochet emotional support carrot pattern: an Emotional Support Carrot amigurumi, about 10 cm tall in DK yarn with a 2.5 mm hook. A plump orange carrot hugs itself with two short arms crossed over its belly, with a bushy top of green leaves, closed smiling eyes, pink cheeks and a few ridge stitches. You need about 35 m of yarn: 20 m orange, 5 m green, 5 m dark green and 5 m pink. Plan on roughly 1 hour. Make it as a small gift for a friend who needs a hug, or keep it as a shelf buddy for the garden-minded. You can spin the 3D model to check how the arms cross and follow the round-by-round pattern.
How to crochet the Emotional Support Carrot
Beginner-friendly · 10 cm tall · about 2 h · DK yarn · 2.5 mm hook
- Crochet the 10 pieces in rounds: Carrot, Tall leaf, Middle leaf ×2, Low leaf ×2, Arm ×2, Cheek ×2 (34 rounds in all).
- Stuff and put it together in 9 steps; each one lights up where it goes on the 3D model.
- Add the face: safety eyes by round and stitch, or embroider them for a child under 3.
Every round with its stitch count is in the Pattern tab below, and in the free printable PDF.
What you'll need
0 of 9 gathered
Gauge
1 sc ≈ 4 mm wide, 1 round ≈ 3.6 mm tall (10 cm ≈ 25 sc × 28 rounds); yarn about 1.9 mm thick. The gauge sets the size of the toy; crochet tightly so the stuffing does not show.
Worked in
Continuous spiral rounds. Don't join. Move a stitch marker up every round.
Parts
0 of 25 rounds done
- Size before assembly: about 4.9 cm at the widest, 6 cm long; 20 rounds.
- → Start stuffing (firmly) and keep adding as you decrease.
- Top up the stuffing if needed. Fasten off leaving a 15 cm tail; with the needle weave it through the front loops of all 6 stitches of the last round, pull tight and hide the end inside.
- Flat motif — leaf (pointed leaf, worked in rounds, one layer of fabric), about 3.7 × 1.1 cm; 1 row.
- Fasten off leaving a long tail (~30 cm) for sewing. Do not stuff. Weave in the starting tail, pin the motif out to shape on a soft surface and steam it lightly.
- Flat motif — leaf (pointed leaf, worked in rounds, one layer of fabric), about 2.9 × 1.1 cm; 1 row.
- Fasten off leaving a long tail (~30 cm) for sewing. Do not stuff. Weave in the starting tail, pin the motif out to shape on a soft surface and steam it lightly.
- Of these: side, left — 1; side, right — 1. Flat motif — leaf (pointed leaf, worked in rounds, one layer of fabric), about 2.5 × 1.1 cm; 1 row.
- Fasten off leaving a long tail (~30 cm) for sewing. Do not stuff. Weave in the starting tail, pin the motif out to shape on a soft surface and steam it lightly.
- Of these: upper — 1; lower — 1. Size before assembly: about 1.2 cm at the widest, 3.1 cm long; 9 rounds.
- Fasten off leaving a long tail (30–40 cm) for sewing. Stuff lightly just before sewing it on; a little less near the edge, then add a pinch when the seam is nearly done.
- A flat circle about 1.5 cm across; 2 rounds.
- Fasten off leaving a long tail (30–40 cm) for sewing. Do not stuff.
Nobody has shown theirs yet. Be the first.
Sign in to show yours
No questions yet
Ask the first one — the author and the AI helper both read here.
Make this toy yours
Open it in the 3D editor: change the colours, the size of any piece, or ask the AI in words. Your version gets its own pattern.
Try asking:
