Baby Tree Creature in a Pot
- Difficulty
- 1/3
- Weirdness
- 1/5
- Times crocheted
- 0
Free crochet mushroom pattern: a Leggy Mushroom amigurumi, about 14 cm tall in DK yarn with a 2.5 mm hook. The mushroom has a red cap with white spots, a cream stem with a smiling face, tiny hands and very long thin legs that stretch out in front of it, ending in brown boots. You need about 140 m of yarn: 60 m cream, 30 m red, 20 m white, 15 m beige, 5 m brown, 5 m tan and 5 m light pink. Plan on roughly 5 hours. Pick it for a gnome-core shelf, a gift for a friend who is always on the move, or a funny toy for a tall-legs collection. Turn the 3D model around and follow the round-by-round pattern.
How to crochet the Leggy Mushroom
Advanced · 14 cm tall · about 5 h · DK yarn · 2.5 mm hook
- Crochet the 18 pieces in rounds: Stem body, Cap, Skirt ring, Dot ×5, Small dot ×4, Arm ×2, Cheek ×2, Leg ×2 (120 rounds in all).
- Stuff and put it together in 13 steps; each one lights up where it goes on the 3D model.
- Add the face: safety eyes by round and stitch, or embroider them for a child under 3.
Every round with its stitch count is in the Pattern tab below, and in the free printable PDF.
What you'll need
0 of 12 gathered
Gauge
1 sc ≈ 4 mm wide, 1 round ≈ 3.6 mm tall (10 cm ≈ 25 sc × 28 rounds); yarn about 1.9 mm thick. The gauge sets the size of the toy; crochet tightly so the stuffing does not show.
Worked in
Continuous spiral rounds. Don't join. Move a stitch marker up every round.
Parts
0 of 69 rounds done
- Size before assembly: about 6.8 cm at the widest, 7.8 cm long; 28 rounds.
- → Insert the safety eyes now (positions: see “Face”) and fix the backs. Start stuffing (firmly) and keep adding as you decrease.
- Top up the stuffing if needed. Fasten off leaving a 15 cm tail; with the needle weave it through the front loops of all 6 stitches of the last round, pull tight and hide the end inside.
- Size before assembly: about 9.3 cm at the widest, 6.3 cm long; 29 rounds.
- Change to beige (pull it through on the last yarn-over of R19).
- → Start stuffing (moderately) and keep adding as you decrease.
- Top up the stuffing if needed. Fasten off leaving a 15 cm tail; with the needle weave it through the front loops of all 6 stitches of the last round, pull tight and hide the end inside.
- Size before assembly: about 7.7 cm at the widest, 0.8 cm long; 3 rounds.
- Fasten off leaving a long tail (30–40 cm) for sewing. Do not stuff.
- Of these: top — 1; front — 1; side — 2 (left and right); back — 1. A flat circle about 2.3 cm across; 3 rounds.
- Fasten off leaving a long tail (30–40 cm) for sewing. Do not stuff.
- Of these: on the cap — 4 (1 pair, left and right, and 2 single). A flat circle about 1.5 cm across; 2 rounds.
- Fasten off leaving a long tail (30–40 cm) for sewing. Do not stuff.
- Size before assembly: about 1.3 cm at the widest, 2 cm long; 6 rounds.
- Fasten off leaving a long tail (30–40 cm) for sewing. Stuff lightly just before sewing it on; a little less near the edge, then add a pinch when the seam is nearly done.
- A flat circle about 1.5 cm across; 2 rounds.
- Fasten off leaving a long tail (30–40 cm) for sewing. Do not stuff.
- Size before assembly: an oval about 3.2 × 2 cm at the widest, 16.6 cm long; 47 rounds. The piece is oval: the rounds go around the chain, and on the finished toy the chain (the long side of the oval) runs vertically, top to bottom; the starting chain is at the front of the piece (on the finished toy). The round-start marker is at a turn of the oval, on the piece's centre line; R1 starts there, so no shift is needed. The increases fall on the turns.
- With tan: ch 5.
- Change to brown (pull it through on the last yarn-over of R2).
- Change to cream (pull it through on the last yarn-over of R6).
- Fasten off leaving a long tail (30–40 cm) for sewing. Stuff lightly just before sewing it on; a little less near the edge, then add a pinch when the seam is nearly done.
Nobody has shown theirs yet. Be the first.
Sign in to show yours
No questions yet
Ask the first one — the author and the AI helper both read here.
Make this toy yours
Open it in the 3D editor: change the colours, the size of any piece, or ask the AI in words. Your version gets its own pattern.
Try asking:
