Green Dino with a Red Saddle
- Difficulty
- 2/3
- Weirdness
- 1/5
- Times crocheted
- 0
A crochet amigurumi inspired by Jigglypuff from Pokémon: a round pink puff with big teal eyes, pointed ears and a curl on the forehead. About 10 cm tall in DK yarn with a 2.5 mm hook. A free pattern with every round counted, a 3D model to turn around and a printable PDF. Unofficial fan-made design, not affiliated with or endorsed by Pokémon.
How to crochet the Singing Pink Puff
Beginner-friendly · 10 cm tall · about 2 h · DK yarn · 2.5 mm hook
- Crochet the 8 pieces in rounds: Body, Ear ×2, Hair curl, Arm ×2, Foot ×2 (59 rounds in all).
- Stuff and put it together in 5 steps; each one lights up where it goes on the 3D model.
- Add the face: safety eyes by round and stitch, or embroider them for a child under 3.
Every round with its stitch count is in the Pattern tab below, and in the free printable PDF.
What you'll need
0 of 7 gathered
Gauge
1 sc ≈ 4 mm wide, 1 round ≈ 3.6 mm tall (10 cm ≈ 25 sc × 28 rounds); yarn about 1.9 mm thick. The gauge sets the size of the toy; crochet tightly so the stuffing does not show.
Worked in
Continuous spiral rounds. Don't join. Move a stitch marker up every round.
Parts
0 of 41 rounds done
- Size before assembly: about 8.6 cm at the widest, 8.6 cm long; 32 rounds.
- → Insert the safety eyes now (positions: see “Face”) and fix the backs. Start stuffing (firmly) and keep adding as you decrease.
- Top up the stuffing if needed. Fasten off leaving a 15 cm tail; with the needle weave it through the front loops of all 6 stitches of the last round, pull tight and hide the end inside.
- Size before assembly: about 4.1 cm at the widest, 2.4 cm long; 8 rounds. Multi-colour rounds are listed stitch by stitch from the round-start marker; keep the round start on the piece's centre front line (as it sits on the finished toy). The order is for right-handed crocheting (right to left on the outside); left-handed: reverse it.
- Fasten off leaving a long tail (30–40 cm) for sewing. Do not stuff. Shape it into a spoon: push the front wall into the back wall (not down to a thin plate) — a concave spoon about 4.7 mm deep in front, a rounded back, and rounded folds of two layers at the sides (about 5.7 mm thick); about 41 mm wide. Keep the opening a curve, hollow side forward, not a straight line.<!-- (spoon 55 %) -->
- Size before assembly: about 1.3 cm at the widest, 3.4 cm long; 10 rounds.
- Fasten off leaving a long tail (30–40 cm) for sewing. Stuff lightly just before sewing it on; a little less near the edge, then add a pinch when the seam is nearly done. Bend ≈ 330° around round 2<!-- the bend spreads over 7 rounds --><!-- coil 2 -->. The piece rolls up into a spiral (about 0.9 turns) from round 2 to its tip: after stuffing, roll it up starting from the tip (round 1) toward the side that faces down on the finished toy; the turns lie close, each wider than the last. From the tip to round 2 tack neighbouring turns together with 2–3 stitches of matching yarn every 3–4 rounds and hide the yarn inside.
- Size before assembly: about 1.3 cm at the widest, 1.3 cm long; 4 rounds.
- Fasten off leaving a long tail (30–40 cm) for sewing. Stuff lightly just before sewing it on; a little less near the edge, then add a pinch when the seam is nearly done.
- Size before assembly: about 1.6 cm at the widest, 1.5 cm long; 5 rounds.
- Fasten off leaving a long tail (30–40 cm) for sewing. Stuff lightly only and press it flat to about 8 mm thick.<!-- flattened 50 % -->
Nobody has shown theirs yet. Be the first.
Sign in to show yours
No questions yet
Ask the first one — the author and the AI helper both read here.
Make this toy yours
Open it in the 3D editor: change the colours, the size of any piece, or ask the AI in words. Your version gets its own pattern.
Try asking:
