Winnie-the-Pooh with a Honey Pot
- Difficulty
- 2/3
- Weirdness
- 1/5
- Times crocheted
- 0
A crochet amigurumi inspired by Sonic from Sonic the Hedgehog: a blue hedgehog with swept-back quills, green eyes, white gloves and red sneakers. About 10 cm tall in DK yarn with a 2.5 mm hook. A free pattern with every round counted, a 3D model to turn around and a printable PDF. Unofficial fan-made design, not affiliated with or endorsed by Sega.
How to crochet the Speedy Blue Hedgehog
Beginner-friendly · 10 cm tall · about 2 h · DK yarn · 2.5 mm hook
- Crochet the 10 pieces in rounds: Body, Ear ×2, Quill ×3, Gloved arm ×2, Sneaker ×2 (61 rounds in all).
- Stuff and put it together in 7 steps; each one lights up where it goes on the 3D model.
- Add the face: safety eyes by round and stitch, or embroider them for a child under 3.
Every round with its stitch count is in the Pattern tab below, and in the free printable PDF.
What you'll need
0 of 9 gathered
Gauge
1 sc ≈ 4 mm wide, 1 round ≈ 3.6 mm tall (10 cm ≈ 25 sc × 28 rounds); yarn about 1.9 mm thick. The gauge sets the size of the toy; crochet tightly so the stuffing does not show.
Worked in
Continuous spiral rounds. Don't join. Move a stitch marker up every round.
Parts
0 of 55 rounds done
- Size before assembly: about 7.7 cm at the widest, 8.7 cm long; 31 rounds. Multi-colour rounds are listed stitch by stitch from the round-start marker; keep the round start on the piece's centre front line (as it sits on the finished toy). The order is for right-handed crocheting (right to left on the outside); left-handed: reverse it.
- Change to blue (pull it through on the last yarn-over of R11).
- Change to blue (pull it through on the last yarn-over of R22).
- → Insert the safety eyes now (positions: see “Face”) and fix the backs. Start stuffing (firmly) and keep adding as you decrease.
- Top up the stuffing if needed. Fasten off leaving a 15 cm tail; with the needle weave it through the front loops of all 6 stitches of the last round, pull tight and hide the end inside.
- Size before assembly: about 2.9 cm at the widest, 1.7 cm long; 6 rounds. Multi-colour rounds are listed stitch by stitch from the round-start marker; keep the round start on the piece's centre front line (as it sits on the finished toy). The order is for right-handed crocheting (right to left on the outside); left-handed: reverse it.
- Fasten off leaving a long tail (30–40 cm) for sewing. Do not stuff. Shape it into a spoon: push the front wall into the back wall (not down to a thin plate) — a concave spoon about 3.3 mm deep in front, a rounded back, and rounded folds of two layers at the sides (about 5.7 mm thick); about 29 mm wide. Keep the opening a curve, hollow side forward, not a straight line.<!-- (spoon 55 %) -->
- Of these: top — 1; low — 1; mid — 1. Size before assembly: about 3.2 cm at the widest, 4.2 cm long; 12 rounds.
- Fasten off leaving a long tail (30–40 cm) for sewing. Stuff firmly just before sewing it on; a little less near the edge, then add a pinch when the seam is nearly done.
- Size before assembly: about 1.2 cm at the widest, 1.7 cm long; 5 rounds.
- Fasten off leaving a long tail (30–40 cm) for sewing. Stuff lightly just before sewing it on; a little less near the edge, then add a pinch when the seam is nearly done.
- Size before assembly: about 2 cm at the widest, 2.2 cm long; 7 rounds.
- Change to white (pull it through on the last yarn-over of R3).
- Change to red (pull it through on the last yarn-over of R4).
- Fasten off leaving a long tail (30–40 cm) for sewing. Stuff lightly, then press the piece slightly flat (oval cross-section; flattened 40 %).
Nobody has shown theirs yet. Be the first.
Sign in to show yours
No questions yet
Ask the first one — the author and the AI helper both read here.
Make this toy yours
Open it in the 3D editor: change the colours, the size of any piece, or ask the AI in words. Your version gets its own pattern.
Try asking:
