Winnie-the-Pooh with a Honey Pot
- Difficulty
- 2/3
- Weirdness
- 1/5
- Times crocheted
- 0
A crochet amigurumi inspired by Pompompurin from Sanrio: a golden puppy with floppy ears and a little brown beret. About 12 cm tall in DK yarn with a 2.5 mm hook. A free pattern with every round counted, a 3D model to turn around and a printable PDF. Unofficial fan-made design, not affiliated with or endorsed by Sanrio.
How to crochet the Pudding Puppy in a Beret
Intermediate · 12 cm tall · about 3 h · DK yarn · 2.5 mm hook
- Crochet the 11 pieces in rounds: Body, Head, Ear ×2, Beret, Beret stalk, Arm ×2, Leg ×2, Tail (89 rounds in all).
- Stuff and put it together in 8 steps; each one lights up where it goes on the 3D model.
- Add the face: safety eyes by round and stitch, or embroider them for a child under 3.
Every round with its stitch count is in the Pattern tab below, and in the free printable PDF.
What you'll need
0 of 8 gathered
Gauge
1 sc ≈ 4 mm wide, 1 round ≈ 3.6 mm tall (10 cm ≈ 25 sc × 28 rounds); yarn about 1.9 mm thick. The gauge sets the size of the toy; crochet tightly so the stuffing does not show.
Worked in
Continuous spiral rounds. Don't join. Move a stitch marker up every round.
Parts
0 of 71 rounds done
- Size before assembly: about 7.4 cm at the widest, 4.3 cm long; 16 rounds.
- Fasten off leaving a long tail (30–40 cm) for sewing. Stuff firmly just before sewing it on; a little less near the edge, then add a pinch when the seam is nearly done.
- Size before assembly: about 8.7 cm at the widest, 6.2 cm long; 27 rounds.
- → Insert the safety eyes now (positions: see “Face”) and fix the backs. Start stuffing (firmly) and keep adding as you decrease.
- Top up the stuffing if needed. Fasten off leaving a 15 cm tail; with the needle weave it through the front loops of all 6 stitches of the last round, pull tight and hide the end inside.
- Size before assembly: about 3.3 cm at the widest, 4.8 cm long; 15 rounds.
- Fasten off leaving a long tail (30–40 cm) for sewing. Do not stuff. Shape it into a spoon: push the front wall into the back wall (not down to a thin plate) — a concave spoon about 3.1 mm deep in front, a rounded back, and rounded folds of two layers at the sides (about 5.7 mm thick); about 33 mm wide. Keep the opening a curve, hollow side forward, not a straight line.<!-- (spoon 45 %) --> Bend ≈ 90° around round 15<!-- the bend spreads over 3 rounds --><!-- drape relax_mm 6 twist 1 -->. The piece is soft and unstuffed: do not tack a fold. Sewn on as the assembly says, it bends over the head by itself and hangs down; the inner side of the bend faces down on the finished toy (on the piece: in round 15, 0.5 st from the centre bottom line, toward the back <!-- st 0.67 back -->). If the ear sticks out, smooth it down along the head by hand.
- Size before assembly: about 5.7 cm at the widest, 1.5 cm long; 9 rounds.
- Fasten off leaving a long tail (30–40 cm) for sewing. Do not stuff.
- Size before assembly: about 0.5 cm at the widest, 0.9 cm long; 3 rounds.
- Fasten off leaving a long tail (30–40 cm) for sewing. Stuff lightly just before sewing it on; a little less near the edge, then add a pinch when the seam is nearly done.
- Size before assembly: about 1.6 cm at the widest, 2.3 cm long; 7 rounds.
- Fasten off leaving a long tail (30–40 cm) for sewing. Stuff lightly just before sewing it on; a little less near the edge, then add a pinch when the seam is nearly done.
- Size before assembly: about 2.4 cm at the widest, 2.1 cm long; 7 rounds.
- Fasten off leaving a long tail (30–40 cm) for sewing. Stuff firmly just before sewing it on; a little less near the edge, then add a pinch when the seam is nearly done.
- Size before assembly: about 1.5 cm at the widest, 1.7 cm long; 5 rounds.
- → Start stuffing (firmly) and keep adding as you decrease.
- Top up the stuffing if needed. Fasten off leaving a 15 cm tail; with the needle weave it through the front loops of all 6 stitches of the last round, pull tight and hide the end inside.
Nobody has shown theirs yet. Be the first.
Sign in to show yours
No questions yet
Ask the first one — the author and the AI helper both read here.
Make this toy yours
Open it in the 3D editor: change the colours, the size of any piece, or ask the AI in words. Your version gets its own pattern.
Try asking:
