Winnie-the-Pooh with a Honey Pot
- Difficulty
- 2/3
- Weirdness
- 1/5
- Times crocheted
- 0
Free crochet bunny pattern: a Buck Tooth Bunny amigurumi, about 8 cm tall in DK yarn with a 2.5 mm hook. A round grey bunny with long floppy ears lined in pink, crossed derpy eyes, a pink nose and two big white buck teeth. You need about 70 m of yarn: 55 m grey, 5 m pink, 5 m light grey and 5 m coral. Plan on roughly 2 hours. It is a goofy little gift for anyone who needs a laugh, or a funny shelf buddy for bunny fans. Spin the 3D model and follow the round-by-round pattern.
How to crochet the Buck Tooth Bunny
Beginner-friendly · 8 cm tall · about 2 h · DK yarn · 2.5 mm hook
- Crochet the 8 pieces in rounds: Body with head, Long floppy ear ×2, Foot ×2, Pompom tail, Cheek ×2 (61 rounds in all).
- Stuff and put it together in 5 steps; each one lights up where it goes on the 3D model.
- Add the face: safety eyes by round and stitch, or embroider them for a child under 3.
Every round with its stitch count is in the Pattern tab below, and in the free printable PDF.
What you'll need
0 of 9 gathered
Gauge
1 sc ≈ 4 mm wide, 1 round ≈ 3.6 mm tall (10 cm ≈ 25 sc × 28 rounds); yarn about 1.9 mm thick. The gauge sets the size of the toy; crochet tightly so the stuffing does not show.
Worked in
Continuous spiral rounds. Don't join. Move a stitch marker up every round.
Parts
0 of 52 rounds done
- Size before assembly: about 9.3 cm at the widest, 7.7 cm long; 31 rounds.
- → Insert the safety eyes now (positions: see “Face”) and fix the backs. Start stuffing (firmly) and keep adding as you decrease.
- Top up the stuffing if needed. Fasten off leaving a 15 cm tail; with the needle weave it through the front loops of all 6 stitches of the last round, pull tight and hide the end inside.
- Size before assembly: about 3.6 cm at the widest, 5.7 cm long; 17 rounds. Multi-colour rounds are listed stitch by stitch from the round-start marker; keep the round start on the piece's centre bottom line (as it sits on the finished toy). The order is for right-handed crocheting (right to left on the outside); left-handed: reverse it.
- Fasten off leaving a long tail (30–40 cm) for sewing. Do not stuff. Shape it into a spoon: push the front wall into the back wall (not down to a thin plate) — a concave spoon about 3.8 mm deep in front, a rounded back, and rounded folds of two layers at the sides (about 5.7 mm thick); about 36 mm wide. Keep the opening a curve, hollow side forward, not a straight line.<!-- (spoon 50 %) --> Bend ≈ 90° around round 17<!-- the bend spreads over 3 rounds --><!-- drape relax_mm 6 twist 0 -->. The piece is soft and unstuffed: do not tack a fold. Sewn on as the assembly says, it bends over the head by itself and hangs down; the inner side of the bend faces down on the finished toy (on the piece: in round 17, 0.5 st from the centre bottom line, toward the back <!-- st 0.64 back -->). Let it hang still turned the way it is sewn on (pinch it a little at the seam): its inside stays visible, it does not lie against the head.
- Size before assembly: about 1.6 cm at the widest, 1.6 cm long; 5 rounds.
- Fasten off leaving a long tail (30–40 cm) for sewing. Stuff firmly just before sewing it on; a little less near the edge, then add a pinch when the seam is nearly done.
- Size before assembly: about 2.1 cm at the widest, 1.6 cm long; 6 rounds.
- → Start stuffing (firmly) and keep adding as you decrease.
- Top up the stuffing if needed. Fasten off leaving a 15 cm tail; with the needle weave it through the front loops of all 6 stitches of the last round, pull tight and hide the end inside.
- A flat circle about 1.5 cm across; 2 rounds.
- Fasten off leaving a long tail (30–40 cm) for sewing. Do not stuff.
Nobody has shown theirs yet. Be the first.
Sign in to show yours
No questions yet
Ask the first one — the author and the AI helper both read here.
Make this toy yours
Open it in the 3D editor: change the colours, the size of any piece, or ask the AI in words. Your version gets its own pattern.
Try asking:
