Winnie-the-Pooh with a Honey Pot
- Difficulty
- 2/3
- Weirdness
- 1/5
- Times crocheted
- 0
Free crochet corgi keychain pattern: a Corgi Butt Keychain amigurumi, about 6 cm tall in fingering yarn with a 2 mm hook. The round fluffy back of a corgi: an orange ball with a white heart-shaped bottom, a tiny tail nub, two stubby white-socked paws, pointed ears peeking over the top and a brown keyring loop. You need about 40 m of yarn: 25 m orange, 5 m white, 5 m dark brown and 5 m pink. Plan on roughly 1 hour. Hang it on your keys or a bag, or give it to a corgi owner who knows exactly which end of the dog this is. You can spin the 3D model and follow the round-by-round pattern.
How to crochet the Corgi Butt Keychain
Beginner-friendly · 6 cm tall · about 2 h · fingering yarn · 2 mm hook
- Crochet the 8 pieces in rounds: Fluffy back, White heart bottom, Paw ×2, Tail nub, Ear ×2, Key loop (47 rounds in all).
- Stuff and put it together in 6 steps; each one lights up where it goes on the 3D model.
Every round with its stitch count is in the Pattern tab below, and in the free printable PDF.
What you'll need
0 of 9 gathered
Gauge
1 sc ≈ 3 mm wide, 1 round ≈ 2.7 mm tall (10 cm ≈ 33 sc × 37 rounds); yarn about 1.4 mm thick. The gauge sets the size of the toy; crochet tightly so the stuffing does not show.
Worked in
Continuous spiral rounds. Don't join. Move a stitch marker up every round.
Parts
0 of 40 rounds done
- Size before assembly: about 5.6 cm at the widest, 4.3 cm long; 24 rounds.
- → Start stuffing (firmly) and keep adding as you decrease.
- Top up the stuffing if needed. Fasten off leaving a 15 cm tail; with the needle weave it through the front loops of all 6 stitches of the last round, pull tight and hide the end inside.
- Flat motif — heart (worked in rounds, one layer of fabric), about 3.6 × 3.7 cm; 5 rows.
- Fasten off leaving a long tail (~30 cm) for sewing. Do not stuff. Weave in the starting tail, pin the motif out to shape on a soft surface and steam it lightly.
- Size before assembly: about 1.5 cm at the widest, 1.1 cm long; 5 rounds.
- Change to orange (pull it through on the last yarn-over of R3).
- Fasten off leaving a long tail (30–40 cm) for sewing. Stuff lightly, then press the piece slightly flat (oval cross-section; flattened 40 %).
- Size before assembly: about 0.9 cm at the widest, 0.7 cm long; 3 rounds.
- Fasten off leaving a long tail (30–40 cm) for sewing. Stuff moderately just before sewing it on; a little less near the edge, then add a pinch when the seam is nearly done.
- Size before assembly: about 1.9 cm at the widest, 1.9 cm long; 8 rounds. Multi-colour rounds are listed stitch by stitch from the round-start marker; keep the round start on the piece's centre back line (as it sits on the finished toy). The order is for right-handed crocheting (right to left on the outside); left-handed: reverse it.
- Fasten off leaving a long tail (30–40 cm) for sewing. Do not stuff. Shape it into a spoon: push the front wall into the back wall (not down to a thin plate) — a concave spoon about 1.6 mm deep in front, a rounded back, and rounded folds of two layers at the sides (about 4.2 mm thick); about 19 mm wide. Keep the opening a curve, hollow side forward, not a straight line.<!-- (spoon 40 %) -->
- Size before assembly: about 1.5 cm at the widest (lies flat); 2 rounds. Each piece is two circles (front and back): make 2 circles — 1 as below and 1 plain in dark brown (same rounds, no colour changes).
- Fasten off. Hold a front and a plain circle wrong sides together and sc around through both layers: 16 sc. Do not stuff. Leave a long tail (~30 cm) for sewing.
Nobody has shown theirs yet. Be the first.
Sign in to show yours
No questions yet
Ask the first one — the author and the AI helper both read here.
Make this toy yours
Open it in the 3D editor: change the colours, the size of any piece, or ask the AI in words. Your version gets its own pattern.
Try asking:
