Winnie-the-Pooh with a Honey Pot
- Difficulty
- 2/3
- Weirdness
- 1/5
- Times crocheted
- 0
Free crochet duck keychain pattern: a Duckling Keychain amigurumi, about 6 cm tall in fingering yarn with a 2.0 mm hook. It is a tiny round yellow duckling with an orange bill, pink cheeks, black bead eyes and a silver-grey loop on top for a key ring. You need about 35 m of yarn: 20 m yellow, 5 m orange, 5 m silver and 5 m blush pink. Plan on roughly 1 hour. Clip it to keys or a bag, or hang it on a tree as a little ornament. Spin the 3D model and follow the round-by-round pattern.
How to crochet the Duckling Keychain
Beginner-friendly · 6 cm tall · about 2 h · fingering yarn · 2 mm hook
- Crochet the 10 pieces in rounds: Head-body, Bill, Wing ×2, Webbed foot ×2, Cheek ×2, Tail, Key ring loop (39 rounds in all).
- Stuff and put it together in 7 steps; each one lights up where it goes on the 3D model.
- Add the face: safety eyes by round and stitch, or embroider them for a child under 3.
Every round with its stitch count is in the Pattern tab below, and in the free printable PDF.
What you'll need
0 of 9 gathered
Gauge
1 sc ≈ 3 mm wide, 1 round ≈ 2.7 mm tall (10 cm ≈ 33 sc × 37 rounds); yarn about 1.4 mm thick. The gauge sets the size of the toy; crochet tightly so the stuffing does not show.
Worked in
Continuous spiral rounds. Don't join. Move a stitch marker up every round.
Parts
0 of 35 rounds done
- Size before assembly: about 4.1 cm at the widest, 4.3 cm long; 21 rounds.
- → Insert the safety eyes now (positions: see “Face”) and fix the backs. Start stuffing (firmly) and keep adding as you decrease.
- Top up the stuffing if needed. Fasten off leaving a 15 cm tail; with the needle weave it through the front loops of all 6 stitches of the last round, pull tight and hide the end inside.
- Size before assembly: an oval about 1.7 × 0.8 cm at the widest, 0.7 cm long; 3 rounds. The piece is oval: the rounds go around the chain, and on the finished toy the chain (the long side of the oval) runs side to side; the starting chain is at the front of the piece (on the finished toy). The round-start marker is in the middle of a long side (the piece's centre line), while R1 starts at a turn: after R1 shift the round start — sc 2 more (not counted in any round) and place the marker there. The increases fall on the turns.
- With orange: ch 5.
- Fasten off leaving a long tail (30–40 cm) for sewing. Stuff lightly, then press the piece slightly flat (oval cross-section; flattened 45 %).
- A flat oval about 2.2 × 1.6 cm; 3 rounds. Worked around a chain, so it is an oval: sew it on with its long side (along the chain) running front to back. The round-start marker is in the middle of a long side (the piece's centre line), while R1 starts at a turn: after R1 shift the round start — sc 1 more (not counted in any round) and place the marker there. The increases fall on the turns.
- With yellow: ch 4.
- Fasten off leaving a long tail (30–40 cm) for sewing. Do not stuff.
- Size before assembly: an oval about 1.4 × 0.8 cm at the widest, 0.7 cm long; 3 rounds. The piece is oval: the rounds go around the chain, and on the finished toy the chain (the long side of the oval) runs side to side; the starting chain is at the front of the piece (on the finished toy). The round-start marker is in the middle of a long side (the piece's centre line), while R1 starts at a turn: after R1 shift the round start — sc 1 more (not counted in any round) and place the marker there. The increases fall on the turns.
- With orange: ch 4.
- Fasten off leaving a long tail (30–40 cm) for sewing. Do not stuff. Press the piece flat (the opening becomes a straight line), front and back walls together.<!-- flattened 85 % -->
- A flat circle about 1 cm across; 2 rounds.
- Fasten off leaving a long tail (30–40 cm) for sewing. Do not stuff.
- Size before assembly: about 0.9 cm at the widest, 0.9 cm long; 4 rounds.
- Fasten off leaving a long tail (30–40 cm) for sewing. Stuff lightly, then press the piece slightly flat (oval cross-section; flattened 45 %).
- Size before assembly: about 1.5 cm at the widest, 0.8 cm long; 3 rounds. Each piece is two circles (front and back): make 2 circles — 1 as below and 1 plain in silver (same rounds, no colour changes).
- Fasten off. Hold a front and a plain circle wrong sides together and sc around through both layers: 16 sc. Do not stuff. Leave a long tail (~30 cm) for sewing.
Nobody has shown theirs yet. Be the first.
Sign in to show yours
No questions yet
Ask the first one — the author and the AI helper both read here.
Make this toy yours
Open it in the 3D editor: change the colours, the size of any piece, or ask the AI in words. Your version gets its own pattern.
Try asking:
