Winnie-the-Pooh with a Honey Pot
- Difficulty
- 2/3
- Weirdness
- 1/5
- Times crocheted
- 0
Free crochet duck pattern: a Leggy Duck amigurumi, about 7 cm tall in DK yarn with a 2.5 mm hook. It is a round yellow duck with an orange bill, pink cheeks, small wings and very long thin orange legs that end in big flat feet. You need about 75 m of yarn: 30 m dark orange, 30 m yellow, 5 m orange, 5 m dark yellow and 5 m pink. Plan on roughly 3 hours. It works as a quirky bath-time-themed shelf toy or a gift for duck fans. Rotate the 3D model to check every angle and follow the round-by-round pattern.
How to crochet the Leggy Duck
Intermediate · 7 cm tall · about 3 h · DK yarn · 2.5 mm hook
- Crochet the 9 pieces in rounds: Duck head and body, Long leg ×2, Bill, Tail, Wing ×2, Cheek ×2 (78 rounds in all).
- Stuff and put it together in 6 steps; each one lights up where it goes on the 3D model.
- Add the face: safety eyes by round and stitch, or embroider them for a child under 3.
Every round with its stitch count is in the Pattern tab below, and in the free printable PDF.
What you'll need
0 of 10 gathered
Gauge
1 sc ≈ 4 mm wide, 1 round ≈ 3.6 mm tall (10 cm ≈ 25 sc × 28 rounds); yarn about 1.9 mm thick. The gauge sets the size of the toy; crochet tightly so the stuffing does not show.
Worked in
Continuous spiral rounds. Don't join. Move a stitch marker up every round.
Parts
0 of 42 rounds done
- Size before assembly: about 7.5 cm at the widest, 6.1 cm long; 25 rounds.
- → Insert the safety eyes now (positions: see “Face”) and fix the backs. Start stuffing (firmly) and keep adding as you decrease.
- Top up the stuffing if needed. Fasten off leaving a 15 cm tail; with the needle weave it through the front loops of all 6 stitches of the last round, pull tight and hide the end inside.
- Size before assembly: an oval about 3.8 × 2.6 cm at the widest, 12.8 cm long; 37 rounds. The piece is oval: the rounds go around the chain, and on the finished toy the chain (the long side of the oval) runs side to side; the starting chain is at the front of the piece (on the finished toy). The round-start marker is at a turn of the oval, on the piece's centre line; R1 starts there, so no shift is needed. The increases fall on the turns.
- With dark orange: ch 5.
- Fasten off leaving a long tail (30–40 cm) for sewing. Stuff lightly just before sewing it on; a little less near the edge, then add a pinch when the seam is nearly done.
- Size before assembly: an oval about 3.6 × 1.6 cm at the widest, 2 cm long; 6 rounds. The piece is oval: the rounds go around the chain, and on the finished toy the chain (the long side of the oval) runs side to side; the starting chain is at the front of the piece (on the finished toy). The round-start marker is in the middle of a long side (the piece's centre line), while R1 starts at a turn: after R1 shift the round start — sc 2 more (not counted in any round) and place the marker there. The increases fall on the turns.
- With orange: ch 7.
- Fasten off leaving a long tail (30–40 cm) for sewing. Stuff lightly only and press it flat to about 1.4 cm thick.<!-- flattened 60 % -->
- Size before assembly: about 1.3 cm at the widest, 1.6 cm long; 5 rounds.
- Fasten off leaving a long tail (30–40 cm) for sewing. Stuff lightly only and press it flat to about 6 mm thick.<!-- flattened 55 % -->
- A flat oval about 3.8 × 2.2 cm; 3 rounds. Worked around a chain, so it is an oval: sew it on with its long side (along the chain) running front to back. The round-start marker is in the middle of a long side (the piece's centre line), while R1 starts at a turn: after R1 shift the round start — sc 2 more (not counted in any round) and place the marker there. The increases fall on the turns.
- With dark yellow: ch 6.
- Fasten off leaving a long tail (30–40 cm) for sewing. Do not stuff.
- A flat circle about 1.5 cm across; 2 rounds.
- Fasten off leaving a long tail (30–40 cm) for sewing. Do not stuff.
Nobody has shown theirs yet. Be the first.
Sign in to show yours
No questions yet
Ask the first one — the author and the AI helper both read here.
Make this toy yours
Open it in the 3D editor: change the colours, the size of any piece, or ask the AI in words. Your version gets its own pattern.
Try asking:
