Winnie-the-Pooh with a Honey Pot
- Difficulty
- 2/3
- Weirdness
- 1/5
- Times crocheted
- 0
Free crochet penguin pattern: a Leggy Penguin amigurumi, about 10 cm tall in DK yarn with a 2.5 mm hook. It is a round black and white penguin with a big white belly, wide surprised eyes, an orange beak and very long orange legs. You need about 85 m: 35 m black, 30 m orange, 15 m white and 5 m pink. Plan on roughly 3 hours. Give it to a penguin lover as a winter gift, or let it perch on a desk as a long-legged mascot. Spin the 3D model and follow the round-by-round pattern for the body, flippers and legs.
How to crochet the Leggy Penguin
Intermediate · 10 cm tall · about 3 h · DK yarn · 2.5 mm hook
- Crochet the 11 pieces in rounds: Penguin, White belly, White face patch ×2, Beak, Flipper ×2, Leg ×2, Cheek ×2 (91 rounds in all).
- Stuff and put it together in 7 steps; each one lights up where it goes on the 3D model.
- Add the face: safety eyes by round and stitch, or embroider them for a child under 3.
Every round with its stitch count is in the Pattern tab below, and in the free printable PDF.
What you'll need
0 of 9 gathered
Gauge
1 sc ≈ 4 mm wide, 1 round ≈ 3.6 mm tall (10 cm ≈ 25 sc × 28 rounds); yarn about 1.9 mm thick. The gauge sets the size of the toy; crochet tightly so the stuffing does not show.
Worked in
Continuous spiral rounds. Don't join. Move a stitch marker up every round.
Parts
0 of 53 rounds done
- Size before assembly: about 7 cm at the widest, 8.2 cm long; 29 rounds.
- → Insert the safety eyes now (positions: see “Face”) and fix the backs. Start stuffing (moderately) and keep adding as you decrease.
- Top up the stuffing if needed. Fasten off leaving a 15 cm tail; with the needle weave it through the front loops of all 6 stitches of the last round, pull tight and hide the end inside.
- A flat oval about 7.9 × 5.9 cm; 8 rounds. Worked around a chain, so it is an oval: sew it on with its long side (along the chain) running side to side. The round-start marker is in the middle of a long side (the piece's centre line), while R1 starts at a turn: after R1 shift the round start — sc 2 more (not counted in any round) and place the marker there. The increases fall on the turns.
- With white: ch 7.
- Fasten off leaving a long tail (30–40 cm) for sewing. Do not stuff.
- A flat circle about 2.3 cm across; 3 rounds.
- Fasten off leaving a long tail (30–40 cm) for sewing. Do not stuff.
- Size before assembly: about 1.1 cm at the widest, 0.9 cm long; 3 rounds.
- Fasten off leaving a long tail (30–40 cm) for sewing. Stuff lightly just before sewing it on; a little less near the edge, then add a pinch when the seam is nearly done.
- Size before assembly: about 1.6 cm at the widest, 2.3 cm long; 7 rounds.
- Fasten off leaving a long tail (30–40 cm) for sewing. Stuff lightly just before sewing it on; a little less near the edge, then add a pinch when the seam is nearly done.
- Size before assembly: an oval about 3.2 × 2 cm at the widest, 13.7 cm long; 39 rounds. The piece is oval: the rounds go around the chain, and on the finished toy the chain (the long side of the oval) runs vertically, top to bottom; the starting chain is at the front of the piece (on the finished toy). The round-start marker is at a turn of the oval, on the piece's centre line; R1 starts there, so no shift is needed. The increases fall on the turns.
- With orange: ch 5.
- Fasten off leaving a long tail (30–40 cm) for sewing. Stuff lightly just before sewing it on; a little less near the edge, then add a pinch when the seam is nearly done.
- A flat circle about 1.5 cm across; 2 rounds.
- Fasten off leaving a long tail (30–40 cm) for sewing. Do not stuff.
Nobody has shown theirs yet. Be the first.
Sign in to show yours
No questions yet
Ask the first one — the author and the AI helper both read here.
Make this toy yours
Open it in the 3D editor: change the colours, the size of any piece, or ask the AI in words. Your version gets its own pattern.
Try asking:
