Winnie-the-Pooh with a Honey Pot
- Difficulty
- 2/3
- Weirdness
- 1/5
- Times crocheted
- 0
Free crochet monkey keychain pattern: a Monkey Keychain amigurumi, about 5 cm tall in fingering yarn with a 2 mm hook. It is a round brown monkey head with a tan heart-shaped face, side ears, pink cheeks, a small yellow banana lying on top like a fringe and a ring for your keys. You need about 40 m of yarn: 20 m brown, 5 m tan, 5 m yellow, 5 m silver and 5 m pink. Plan on roughly 1 hour. Clip it to a backpack or keys as a cheerful charm, or tuck it into a small gift. You can rotate the 3D model and follow the round-by-round pattern while you crochet.
How to crochet the Monkey Keychain
Beginner-friendly · 5 cm tall · about 2 h · fingering yarn · 2 mm hook
- Crochet the 8 pieces in rounds: Head ball, Heart face, Ear ×2, Banana, Cheek ×2, Key ring loop (50 rounds in all).
- Stuff and put it together in 6 steps; each one lights up where it goes on the 3D model.
- Add the face: safety eyes by round and stitch, or embroider them for a child under 3.
Every round with its stitch count is in the Pattern tab below, and in the free printable PDF.
What you'll need
0 of 10 gathered
Gauge
1 sc ≈ 3 mm wide, 1 round ≈ 2.7 mm tall (10 cm ≈ 33 sc × 37 rounds); yarn about 1.4 mm thick. The gauge sets the size of the toy; crochet tightly so the stuffing does not show.
Worked in
Continuous spiral rounds. Don't join. Move a stitch marker up every round.
Parts
0 of 39 rounds done
- Size before assembly: about 5 cm at the widest, 4 cm long; 22 rounds.
- → Start stuffing (firmly) and keep adding as you decrease.
- Top up the stuffing if needed. Fasten off leaving a 15 cm tail; with the needle weave it through the front loops of all 6 stitches of the last round, pull tight and hide the end inside.
- Flat motif — heart (worked in rounds, one layer of fabric), about 4.1 × 4.3 cm; 6 rows.
- Fasten off leaving a long tail (~30 cm) for sewing. Do not stuff. Weave in the starting tail, pin the motif out to shape on a soft surface and steam it lightly.
- Size before assembly: about 2.3 cm at the widest, 1.4 cm long; 6 rounds.
- Change to brown (pull it through on the last yarn-over of R2).
- → This piece is not stuffed.
- Fasten off leaving a 15 cm tail; with the needle weave it through the front loops of all 6 stitches of the last round, pull tight and hide the end inside. Do not stuff. Shape it into a dish: rounds 1–3 are the front of the piece, the magic ring its centre. Push the centre in so the front is concave (about 2.1 mm at the centre) and turn rounds 4–6 to the back: they make a thick rounded rim (about 5.9 mm thick) and lie behind as a second layer; the piece is about 23 mm across.<!-- (dish 50 %) -->
- Size before assembly: about 0.9 cm at the widest, 3 cm long; 11 rounds.
- → Start stuffing (firmly) and keep adding as you decrease.
- Top up the stuffing if needed. Fasten off leaving a 15 cm tail; with the needle weave it through the front loops of all 5 stitches of the last round, pull tight and hide the end inside. Bend ≈ 45° around round 5<!-- the bend spreads over 6 rounds -->. After stuffing, bend the piece so the inner side of the bend faces up on the finished toy (on the piece: in round 5, 2 st from the centre front line, upward <!-- st 1.92 up -->). On the inner side draw rounds 4 and 5 together (1 rounds go into the fold): with the needle and matching yarn make 3–4 stitches through the loops of both rounds over about 2 st, pull to the angle and hide the end inside.
- A flat circle about 1 cm across; 2 rounds.
- Fasten off leaving a long tail (30–40 cm) for sewing. Do not stuff.
- Size before assembly: about 1.3 cm at the widest, 0.8 cm long; 3 rounds. Each piece is two circles (front and back): make 2 circles — 1 as below and 1 plain in silver (same rounds, no colour changes).
- Fasten off. Hold a front and a plain circle wrong sides together and sc around through both layers: 14 sc. Do not stuff. Leave a long tail (~30 cm) for sewing.
Nobody has shown theirs yet. Be the first.
Sign in to show yours
No questions yet
Ask the first one — the author and the AI helper both read here.
Make this toy yours
Open it in the 3D editor: change the colours, the size of any piece, or ask the AI in words. Your version gets its own pattern.
Try asking:
