Winnie-the-Pooh with a Honey Pot
- Difficulty
- 2/3
- Weirdness
- 1/5
- Times crocheted
- 0
A free crochet Christmas ornaments pattern for a round white amigurumi bunny bauble with long ears, a striped scarf and a golden cap. The pink-lined ears stand up beside the gold cap and loop, a little pompom tail sits at the back, and the red and green knit scarf adds the holiday touch to this bunny plushie. It is worked in the round in single crochet with fingering yarn and a 2 mm hook and is about 7.8 cm (3 in) tall; the face is embroidered and the ears, cheeks, scarf, tail, cap and loop are sewn on. The page gives a row-by-row pattern with stitch counts and an interactive 3D model to check every piece,.
How to crochet the Bunny Bauble Ornament
Beginner-friendly · 8 cm tall · about 2 h · fingering yarn · 2 mm hook
- Crochet the 9 pieces in rounds: Head-body ball, Long ear ×2, Cheek ×2, Pompom tail, Gold cap, Hanging loop, Striped scarf (59 rounds in all).
- Stuff and put it together in 8 steps; each one lights up where it goes on the 3D model.
- Add the face: safety eyes by round and stitch, or embroider them for a child under 3.
Every round with its stitch count is in the Pattern tab below, and in the free printable PDF.
What you'll need
0 of 11 gathered
Gauge
1 sc ≈ 3 mm wide, 1 round ≈ 2.7 mm tall (10 cm ≈ 33 sc × 37 rounds); yarn about 1.4 mm thick. The gauge sets the size of the toy; crochet tightly so the stuffing does not show.
Worked in
Continuous spiral rounds. Don't join. Move a stitch marker up every round.
Parts
0 of 50 rounds done
- Size before assembly: about 5.4 cm at the widest, 5.4 cm long; 26 rounds.
- → Start stuffing (firmly) and keep adding as you decrease.
- Top up the stuffing if needed. Fasten off leaving a 15 cm tail; with the needle weave it through the front loops of all 6 stitches of the last round, pull tight and hide the end inside.
- Size before assembly: about 1.6 cm at the widest, 3.3 cm long; 13 rounds. Multi-colour rounds are listed stitch by stitch from the round-start marker; keep the round start on the piece's centre front line (as it sits on the finished toy). The order is for right-handed crocheting (right to left on the outside); left-handed: reverse it.
- Fasten off leaving a long tail (30–40 cm) for sewing. Do not stuff. Shape it into a spoon: push the front wall into the back wall (not down to a thin plate) — a concave spoon about 1 mm deep in front, a rounded back, and rounded folds of two layers at the sides (about 4.2 mm thick); about 16 mm wide. Keep the opening a curve, hollow side forward, not a straight line.<!-- (spoon 30 %) -->
- A flat circle about 1 cm across; 2 rounds.
- Fasten off leaving a long tail (30–40 cm) for sewing. Do not stuff.
- Size before assembly: about 0.9 cm at the widest, 1 cm long; 4 rounds.
- → Start stuffing (firmly) and keep adding as you decrease.
- Top up the stuffing if needed. Fasten off leaving a 15 cm tail; with the needle weave it through the front loops of all 5 stitches of the last round, pull tight and hide the end inside.
- Size before assembly: about 2.3 cm at the widest, 1.6 cm long; 8 rounds.
- Fasten off leaving a long tail (30–40 cm) for sewing. Stuff lightly just before sewing it on; a little less near the edge, then add a pinch when the seam is nearly done.
- Size before assembly: about 1.5 cm at the widest (lies flat); 2 rounds. Each piece is two circles (front and back): make 2 circles — 1 as below and 1 plain in soft gold (same rounds, no colour changes).
- Fasten off. Hold a front and a plain circle wrong sides together and sc around through both layers: 16 sc. Do not stuff. Leave a long tail (~30 cm) for sewing.
- Size before assembly: about 5 cm at the widest, 1.1 cm long; 4 rounds.
- Change to holly green (pull it through on the last yarn-over of R1).
- Change to christmas red (pull it through on the last yarn-over of R3).
- Fasten off leaving a long tail (30–40 cm) for sewing. Do not stuff.
Nobody has shown theirs yet. Be the first.
Sign in to show yours
No questions yet
Ask the first one — the author and the AI helper both read here.
Make this toy yours
Open it in the 3D editor: change the colours, the size of any piece, or ask the AI in words. Your version gets its own pattern.
Try asking:
