Winnie-the-Pooh with a Honey Pot
- Difficulty
- 2/3
- Weirdness
- 1/5
- Times crocheted
- 0
Free crochet worry worm pattern: a Worry Worm with a Mustache amigurumi, about 5 cm tall in DK yarn with a 2.5 mm hook. It is a soft green striped worm with a worried little face, slanted brows, rosy cheeks and a big curly chocolate-brown mustache. You need about 35 m of yarn: 15 m lime, 10 m light green, 5 m cocoa and 5 m blush pink. Plan on roughly 1 hour. A pocket-sized worry worm makes a sweet desk buddy or a gift for a friend who needs a smile. Spin the 3D model to see the curled mustache from every side, then follow the round-by-round pattern.
How to crochet the Worry Worm with a Mustache
Beginner-friendly · 5 cm tall · about 2 h · DK yarn · 2.5 mm hook
- Crochet the 5 pieces in rounds: Worm body, Cheek ×2, Mustache half ×2 (49 rounds in all).
- Stuff and put it together in 5 steps; each one lights up where it goes on the 3D model.
- Add the face: safety eyes by round and stitch, or embroider them for a child under 3.
Every round with its stitch count is in the Pattern tab below, and in the free printable PDF.
What you'll need
0 of 9 gathered
Gauge
1 sc ≈ 4 mm wide, 1 round ≈ 3.6 mm tall (10 cm ≈ 25 sc × 28 rounds); yarn about 1.9 mm thick. The gauge sets the size of the toy; crochet tightly so the stuffing does not show.
Worked in
Continuous spiral rounds. Don't join. Move a stitch marker up every round.
Parts
0 of 38 rounds done
- Size before assembly: about 4.6 cm at the widest, 12.4 cm long; 36 rounds.
- Change to light green (pull it through on the last yarn-over of R12).
- → Insert the safety eyes now (positions: see “Face”) and fix the backs. Start stuffing (firmly) and keep adding as you decrease.
- Change to lime (pull it through on the last yarn-over of R15).
- Change to light green (pull it through on the last yarn-over of R19).
- Change to lime (pull it through on the last yarn-over of R23).
- Change to light green (pull it through on the last yarn-over of R27).
- Top up the stuffing if needed. Fasten off leaving a 15 cm tail; with the needle weave it through the front loops of all 6 stitches of the last round, pull tight and hide the end inside. Bend ≈ 230° around round 14<!-- the bend spreads over 3 rounds --><!-- coil 2 pitch 14 -->. The piece rolls up into a spiral (about 0.6 turns) from round 14 to its end: after stuffing, roll it up starting from the last round (round 36) toward the side that faces toward the toy's left on the finished toy; the turns lie close, each wider than the last. From the last round back to round 14 tack neighbouring turns together with 2–3 stitches of matching yarn every 3–4 rounds and hide the yarn inside.
- A flat circle about 1.5 cm across; 2 rounds.
- Fasten off leaving a long tail (30–40 cm) for sewing. Do not stuff.
- Size before assembly: about 0.9 cm at the widest, 3.8 cm long; 11 rounds.
- Fasten off leaving a long tail (30–40 cm) for sewing. Stuff lightly just before sewing it on; a little less near the edge, then add a pinch when the seam is nearly done. Bend ≈ 190° around round 5<!-- the bend spreads over 4 rounds -->. After stuffing, bend the piece so the inner side of the bend faces up on the finished toy (on the piece: in round 5, 1.5 st from the centre front line, upward <!-- st 1.66 up -->). It is a gradual bend: with the needle and matching yarn run a line of stitches along the inner side from round 3 to round 7, one stitch in every round along one column, then pull the yarn until the piece bends to the angle (the inner side gathers by about 4 rounds) and fasten off inside.
Nobody has shown theirs yet. Be the first.
Sign in to show yours
No questions yet
Ask the first one — the author and the AI helper both read here.
Make this toy yours
Open it in the 3D editor: change the colours, the size of any piece, or ask the AI in words. Your version gets its own pattern.
Try asking:
