Winnie-the-Pooh with a Honey Pot
- Difficulty
- 2/3
- Weirdness
- 1/5
- Times crocheted
- 0
Free crochet bunny ornament pattern: a Snow Bunny Ornament amigurumi, about 10 cm tall in DK yarn with a 2.5 mm hook. A round white bunny head with two long ears with pink insides, black bead eyes, a pink nose, rosy cheeks and a mint scarf with a short tail, hung from a red loop. You need about 50 m of yarn: 35 m white, 5 m mint, 5 m red and 5 m pink. Plan on roughly 2 hours. It is a quick, beginner-friendly make that works as a tree ornament, a gift tag topper or a small winter present. Spin the 3D model and follow the round-by-round pattern; the head is one ball worked in the round.
How to crochet the Snow Bunny Ornament
Beginner-friendly · 10 cm tall · about 2 h · DK yarn · 2.5 mm hook
- Crochet the 7 pieces in rounds: Bunny head ball, Ear ×2, Cheek ×2, Scarf end, Hanging loop (47 rounds in all).
- Stuff and put it together in 5 steps; each one lights up where it goes on the 3D model.
- Add the face: safety eyes by round and stitch, or embroider them for a child under 3.
Every round with its stitch count is in the Pattern tab below, and in the free printable PDF.
What you'll need
0 of 9 gathered
Gauge
1 sc ≈ 4 mm wide, 1 round ≈ 3.6 mm tall (10 cm ≈ 25 sc × 28 rounds); yarn about 1.9 mm thick. The gauge sets the size of the toy; crochet tightly so the stuffing does not show.
Worked in
Continuous spiral rounds. Don't join. Move a stitch marker up every round.
Parts
0 of 34 rounds done
- Size before assembly: about 7.5 cm at the widest, 6.1 cm long; 25 rounds.
- Change to mint (pull it through on the last yarn-over of R9).
- Change to white (pull it through on the last yarn-over of R11).
- → Insert the safety eyes now (positions: see “Face”) and fix the backs. Start stuffing (firmly) and keep adding as you decrease.
- Top up the stuffing if needed. Fasten off leaving a 15 cm tail; with the needle weave it through the front loops of all 6 stitches of the last round, pull tight and hide the end inside.
- Size before assembly: about 1.8 cm at the widest, 4.9 cm long; 14 rounds. Multi-colour rounds are listed stitch by stitch from the round-start marker; keep the round start on the piece's centre front line (as it sits on the finished toy). The order is for right-handed crocheting (right to left on the outside); left-handed: reverse it.
- Fasten off leaving a long tail (30–40 cm) for sewing. Stuff it lightly — a thin layer, just enough to hold the walls apart: the ear about 10.8 mm thick, with thick rounded edges. Then shape it into a spoon: push the front wall toward the back wall — a concave spoon about 1.5 mm deep in front, a rounded back; about 18 mm wide. Keep the opening a curve, hollow side forward, not a straight line.<!-- (spoon 40 %) -->
- A flat circle about 1.5 cm across; 2 rounds.
- Fasten off leaving a long tail (30–40 cm) for sewing. Do not stuff.
- Size before assembly: an oval about 1.3 × 0.5 cm at the widest, 1.4 cm long; 4 rounds. The piece is oval: the rounds go around the chain, and on the finished toy the chain (the long side of the oval) runs side to side; the starting chain is at the bottom of the piece (on the finished toy). The round-start marker is in the middle of a long side (the piece's centre line), while R1 starts at a turn: after R1 shift the round start — sc 1 more (not counted in any round) and place the marker there. The increases fall on the turns.
- With mint: ch 4.
- Fasten off leaving a long tail (30–40 cm) for sewing. Do not stuff. Press the piece flat (the opening becomes a straight line), front and back walls together.<!-- flattened 90 % -->
- Size before assembly: about 2.3 cm at the widest, 0.7 cm long; 2 rounds. Each piece is two circles (front and back): make 2 circles — 1 as below and 1 plain in red (same rounds, no colour changes).
- Fasten off. Hold a front and a plain circle wrong sides together and sc around through both layers: 18 sc. Do not stuff. Leave a long tail (~30 cm) for sewing.
Nobody has shown theirs yet. Be the first.
Sign in to show yours
No questions yet
Ask the first one — the author and the AI helper both read here.
Make this toy yours
Open it in the 3D editor: change the colours, the size of any piece, or ask the AI in words. Your version gets its own pattern.
Try asking:
