Winnie-the-Pooh with a Honey Pot
- Difficulty
- 2/3
- Weirdness
- 1/5
- Times crocheted
- 0
A crochet amigurumi inspired by Cinnamoroll from Sanrio: a white puppy with very long floppy ears, blue eyes and a cinnamon-roll tail. About 10 cm tall in DK yarn with a 2.5 mm hook. A free pattern with every round counted, a 3D model to turn around and a printable PDF. Unofficial fan-made design, not affiliated with or endorsed by Sanrio.
How to crochet the Cloud Puppy with Long Ears
Intermediate · 10 cm tall · about 3 h · DK yarn · 2.5 mm hook
- Crochet the 11 pieces in rounds: Body, Head, Ear ×2, Cheek ×2, Arm ×2, Leg ×2, Curly tail (87 rounds in all).
- Stuff and put it together in 7 steps; each one lights up where it goes on the 3D model.
- Add the face: safety eyes by round and stitch, or embroider them for a child under 3.
Every round with its stitch count is in the Pattern tab below, and in the free printable PDF.
What you'll need
0 of 7 gathered
Gauge
1 sc ≈ 4 mm wide, 1 round ≈ 3.6 mm tall (10 cm ≈ 25 sc × 28 rounds); yarn about 1.9 mm thick. The gauge sets the size of the toy; crochet tightly so the stuffing does not show.
Worked in
Continuous spiral rounds. Don't join. Move a stitch marker up every round.
Parts
0 of 70 rounds done
- Size before assembly: about 5.7 cm at the widest, 3.9 cm long; 14 rounds.
- Fasten off leaving a long tail (30–40 cm) for sewing. Stuff firmly just before sewing it on; a little less near the edge, then add a pinch when the seam is nearly done.
- Size before assembly: about 8.7 cm at the widest, 6.2 cm long; 27 rounds.
- → Insert the safety eyes now (positions: see “Face”) and fix the backs. Start stuffing (firmly) and keep adding as you decrease.
- Top up the stuffing if needed. Fasten off leaving a 15 cm tail; with the needle weave it through the front loops of all 6 stitches of the last round, pull tight and hide the end inside.
- Size before assembly: about 4.4 cm at the widest, 9.2 cm long; 27 rounds.
- Fasten off leaving a long tail (30–40 cm) for sewing. Do not stuff. Shape it into a spoon: push the front wall into the back wall (not down to a thin plate) — a concave spoon about 4.6 mm deep in front, a rounded back, and rounded folds of two layers at the sides (about 5.7 mm thick); about 44 mm wide. Keep the opening a curve, hollow side forward, not a straight line.<!-- (spoon 50 %) --> Bend ≈ 90° around round 27<!-- the bend spreads over 3 rounds --><!-- drape relax_mm 6 twist 1 -->. The piece is soft and unstuffed: do not tack a fold. Sewn on as the assembly says, it bends over the head by itself and hangs down; the inner side of the bend faces down on the finished toy (on the piece: in round 27, 1 st from the centre bottom line, toward the back <!-- st 0.96 back -->). If the ear sticks out, smooth it down along the head by hand.
- A flat circle about 1.5 cm across; 2 rounds.
- Fasten off leaving a long tail (30–40 cm) for sewing. Do not stuff.
- Size before assembly: about 1.6 cm at the widest, 2.3 cm long; 7 rounds.
- Fasten off leaving a long tail (30–40 cm) for sewing. Stuff lightly just before sewing it on; a little less near the edge, then add a pinch when the seam is nearly done.
- Size before assembly: about 2.4 cm at the widest, 2.1 cm long; 7 rounds.
- Fasten off leaving a long tail (30–40 cm) for sewing. Stuff firmly just before sewing it on; a little less near the edge, then add a pinch when the seam is nearly done.
- A flat circle about 2.3 cm across; 3 rounds.
- Fasten off leaving a long tail (30–40 cm) for sewing. Do not stuff. Bend ≈ 360° around round 3<!-- the bend spreads over 10 rounds --><!-- coil 2 -->. The piece rolls up into a spiral (about 1 turn) from round 3 to its end: after stuffing, roll it up starting from the last round (round 3) toward the side that faces up on the finished toy; the turns lie close, each wider than the last. From the last round back to round 3 tack neighbouring turns together with 2–3 stitches of matching yarn every 3–4 rounds and hide the yarn inside.
Nobody has shown theirs yet. Be the first.
Sign in to show yours
No questions yet
Ask the first one — the author and the AI helper both read here.
Make this toy yours
Open it in the 3D editor: change the colours, the size of any piece, or ask the AI in words. Your version gets its own pattern.
Try asking:
