Winnie-the-Pooh with a Honey Pot
- Difficulty
- 2/3
- Weirdness
- 1/5
- Times crocheted
- 0
Free crochet goose pattern: a Goose Keychain amigurumi, about 10 cm tall in fingering yarn with a 2 mm hook. It is a tiny white goose with an orange beak and feet, a raised eyebrow for a mischievous honk face and a silver ring on top of its head for your keys. You need about 65 m of yarn: 50 m white, 10 m orange and 5 m silver. Plan on roughly 2 hours. Hang it on your keys or bag as a cheeky little charm; it also makes a fun gift for goose lovers. Spin the 3D model and follow the round-by-round pattern to get the same tiny goose.
How to crochet the Goose Keychain
Intermediate · 10 cm tall · about 2 h · fingering yarn · 2 mm hook
- Crochet the 9 pieces in rounds: Body, Head and neck, Beak, Wing ×2, Tail, Foot ×2, Key ring loop (85 rounds in all).
- Stuff and put it together in 7 steps; each one lights up where it goes on the 3D model.
- Add the face: safety eyes by round and stitch, or embroider them for a child under 3.
Every round with its stitch count is in the Pattern tab below, and in the free printable PDF.
What you'll need
0 of 8 gathered
Gauge
1 sc ≈ 3 mm wide, 1 round ≈ 2.7 mm tall (10 cm ≈ 33 sc × 37 rounds); yarn about 1.4 mm thick. The gauge sets the size of the toy; crochet tightly so the stuffing does not show.
Worked in
Continuous spiral rounds. Don't join. Move a stitch marker up every round.
Parts
0 of 60 rounds done
- Size before assembly: about 5.7 cm at the widest, 6.5 cm long; 30 rounds.
- → Start stuffing (firmly) and keep adding as you decrease.
- Press the piece flat to about 5 cm thick (oval cross-section).<!-- press the piece flat by 12 % --> Top up the stuffing if needed. Fasten off leaving a 15 cm tail; with the needle weave it through the front loops of all 6 stitches of the last round, pull tight and hide the end inside.
- Size before assembly: about 4 cm at the widest, 5.9 cm long; 24 rounds.
- Fasten off leaving a long tail (30–40 cm) for sewing. Insert the safety nose/eyes now, while the piece is open (positions: see “Face”). Stuff firmly just before sewing it on; a little less near the edge, then add a pinch when the seam is nearly done. Bend ≈ 50° around round 15<!-- the bend spreads over 3 rounds -->. After stuffing, bend the piece so the inner side of the bend faces forward on the finished toy (on the piece: in round 15, on the centre front line). It is a gradual bend: with the needle and matching yarn run a line of stitches along the inner side from round 13 to round 17, one stitch in every round along one column, then pull the yarn until the piece bends to the angle (the inner side gathers by about 4 rounds) and fasten off inside.
- Size before assembly: about 1.1 cm at the widest, 1.5 cm long; 6 rounds.
- Fasten off leaving a long tail (30–40 cm) for sewing. Stuff lightly just before sewing it on; a little less near the edge, then add a pinch when the seam is nearly done.
- Size before assembly: about 1.8 cm at the widest, 2.5 cm long; 10 rounds.
- Fasten off leaving a long tail (30–40 cm) for sewing. Stuff lightly only and press it flat to about 8 mm thick.<!-- flattened 55 % -->
- Size before assembly: about 1 cm at the widest, 1.2 cm long; 5 rounds.
- Fasten off leaving a long tail (30–40 cm) for sewing. Stuff lightly only and press it flat to about 5 mm thick.<!-- flattened 50 % -->
- Size before assembly: about 1.4 cm at the widest, 1.7 cm long; 7 rounds.
- Fasten off leaving a long tail (30–40 cm) for sewing. Do not stuff. Press the piece flat (the opening becomes a straight line), front and back walls together.<!-- flattened 85 % -->
- Size before assembly: about 1.5 cm at the widest, 0.8 cm long; 3 rounds. Each piece is two circles (front and back): make 2 circles — 1 as below and 1 plain in silver (same rounds, no colour changes).
- Fasten off. Hold a front and a plain circle wrong sides together and sc around through both layers: 16 sc. Do not stuff. Leave a long tail (~30 cm) for sewing.
Nobody has shown theirs yet. Be the first.
Sign in to show yours
No questions yet
Ask the first one — the author and the AI helper both read here.
Make this toy yours
Open it in the 3D editor: change the colours, the size of any piece, or ask the AI in words. Your version gets its own pattern.
Try asking:
